PM8073 - DESIGN OF PRESSURE VESSELS AND PIPING (Syllabus) 2017-regulation Anna University
PM8073 - DESIGN OF PRESSURE VESSELS AND PIPING (Syllabus) 2017-regulation Anna University
PM8073 |
DESIGN OF PRESSURE VESSELS AND PIPING |
LPTC |
|---|
3003
OBJECTIVES:
• The main objective is to present the industrial related problems, procedures and design.
• Principles for pressure vessels and enhance the understanding of design procedure of pressure vessel and Design of piping layout.
• Principles for pressure vessels and enhance the understanding of design procedure of pressure vessel and Design of piping layout.
UNIT I |
DESIGN OF PIPE FITTINGS AND JOINTS |
9 |
|---|
Stress-strain relationships of elastic materials subjected to tensile, compressive and shear forces; Membrane stresses in shells of revolutions; Theories of failures. Design and schematic of simple bolts and screws. Design and drawing of shafts and couplings.
UNIT II |
DESIGN OF PRESSURE VESSELS |
9 |
|---|
Unfired pressure vessel: Pressure vessel codes; Design of cylindrical and spherical shells under internal and external pressures; Selection and design of flat plate, tori spherical, ellipsoidal, and conical closures; Shell design of tall vertical vessels; Compensations of openings. Vessel supports: Design of skirt, lug, and saddle supports.
UNIT III |
DESIGN OF STORAGE TANK |
9 |
|---|
Liquid storage tanks: Storage tank codes; Classification; Design of shell, bottom plates, self- supported, and column supported roofs; Wind girder; Nozzles and other accessories.
UNIT IV |
FABRICATION AND MATERIALS |
9 |
|---|
Fabrication of equipment: Major fabrication steps; Vessel lining; Materials used in fabrication of Chemical Equipments. Selection of process equipment’s.
UNIT V |
DESIGN OF PIPING NETWORK |
9 |
|---|
Introduction – Flow diagram – piping layout and piping stress Analysis.
TOTAL : 45 PERIODS
OUTCOME:
• Students would develop skill to design and install process equipment’s used widely in achemical industry.
TEXT BOOKS:
1. R.S. Khurmi, “Textbook of Machine design”. S. Chand & Company , XXV Edition, 2005.
2. M.V. Joshi and V.V. Mahajan, “Design of Process Equipment Design”, McMillan India III Edition 1994.
3. Bhattacharyya, B.C., “Introduction to chemical Equipment Design: Mechanical aspects”, CBS Publishers & Distributors, New Delhi.
2. M.V. Joshi and V.V. Mahajan, “Design of Process Equipment Design”, McMillan India III Edition 1994.
3. Bhattacharyya, B.C., “Introduction to chemical Equipment Design: Mechanical aspects”, CBS Publishers & Distributors, New Delhi.
REFERENCES:
1. S.D. Dawande, “Process Design of Equipments”, Central Techno Publications, Nagpur, 2000.
2. Indian Standard Specifications IS-803, 1962; IS-4072, 1967; IS-2825, 1969. Indian Standards Institution, New Delhi.
3. R.H. Perry, “Chemical Engineers’ Handbook”, McGraw-Hill.
4. Ludwig, E.E., Applied Process Design for Chemical and Petrochemical Plants”, Volume I, II, and III, Gulf Publishing Co.
5. J.M. Coulson and J.Richardson, “Chemical Engineering”, Vol. 6, Asian Books Printers Ltd.
2. Indian Standard Specifications IS-803, 1962; IS-4072, 1967; IS-2825, 1969. Indian Standards Institution, New Delhi.
3. R.H. Perry, “Chemical Engineers’ Handbook”, McGraw-Hill.
4. Ludwig, E.E., Applied Process Design for Chemical and Petrochemical Plants”, Volume I, II, and III, Gulf Publishing Co.
5. J.M. Coulson and J.Richardson, “Chemical Engineering”, Vol. 6, Asian Books Printers Ltd.
Comments
Post a Comment