ET4103 - Microcontroller Based System Design (Syllabus) 2021-regulation Anna University

ET4103 - Microcontroller Based System Design (Syllabus) 2021-regulation Anna University

ET4103 MICROCONTROLLER BASED SYSTEM DESIGN  LPTC
3003

OBJECTIVES:
• To teach the architecture of PIC Microcontroller and RISC processor.
• To compare the architecture and programming of 8,16,32 bit RISC processor.
• To teach the implementation of DSP in ARM processor.
• To discuss on memory management, application development in RISC processor.
• To involve Discussions/ Practice/Exercise onto revising & familiarizing the concepts acquired over the 5 Units of the subject for improved employability skills.

UNIT I PIC MICROCONTROLLER 9
Architecture – memory organization – addressing modes – instruction set – PIC programming in Assembly & C –I/O port, Data Conversion, RAM & ROM Allocation, Timer programming, practice in MP-LAB.

UNIT II ARM ARCHITECTURE 9
Architecture – memory organization – addressing modes – The ARM Programmer’s model -Registers – Pipeline - Interrupts – Coprocessors – Interrupt Structure


UNIT III PERIPHERALS OF PIC AND ARM MICROCONTROLLER 9
PIC: ADC, DAC and Sensor Interfacing –Flash and EEPROM memories. ARM: I/O Memory – EEPROM – I/O Ports – SRAM –Timer –UART - Serial Communication with PC – ADC/DAC Interfacing.

UNIT IV ARM MICROCONTROLLER PROGRAMMING 9
ARM general Instruction set – Thumb instruction set –Introduction to DSP on ARM – Implementation example of Filters

UNIT V DESIGN WITH PIC AND ARM MICROCONTROLLERS 9
PIC implementation - Generation of Gate signals for converters and Inverters - Motor Control – Controlling DC/ AC appliances – Measurement of frequency - Stand alone Data Acquisition System –ARM Implementation- Simple ASM/C programs- Loops –Look up table- Block copy- subroutines- Hamming Code.

TOTAL : 45 PERIODS

OUTCOMES: At the end of this course, the students will demonstrate the ability
CO1: To understand the basics and requirement of processor functional blocks.
CO2: Observe the specialty of RISC processor Architecture.
CO3: Incorporate I/O hardware interface of a processor based automation for consumer application with peripherals.
CO4: Incorporate I/O software interface of a processor with peripherals.
CO5: Improved Employability and entrepreneurship capacity due to knowledge up gradation on recent trends in commercial embedded processors

REFERENCES:
1. Steve Furber, ‘ARM system on chip architecture’, Addision Wesley,2010.
2. Andrew N. Sloss, Dominic Symes, Chris Wright, John Rayfield ‘ARM System Developer’s Guide Designing and Optimizing System Software’, Elsevier 2007.
3. Muhammad Ali Mazidi, Rolin D. Mckinlay, Danny Causey ‘ PIC Microcontroller and Embedded Systems using Assembly and C for PIC18’, Pearson Education 2008.
4. John Iovine, ‘PIC Microcontroller Project Book ’, McGraw Hill 2000
5. William Hohl, ‘ ARM Assebly Language’ Fundamentals and Techniques,2009.
6. Rajkamal,”Microcontrollers Architecture, Programming, Interfacing,& System Design,Pearson,2012
7. ARM Architecture Reference Manual, LPC213x User Manual
8. www.Nuvoton.com/websites on Advanced ARM Cortex Processors
Previous
Next

Comments

Post a Comment

Popular posts from this blog

EC8094 - SATELLITE COMMUNICATION (Syllabus) 2017-regulation Anna University

EC8094 - SATELLITE COMMUNICATION (Syllabus) 2017-regulation Anna University EC8094 SATELLITE COMMUNICATION  LPTC 3003 OBJECTIVES: • Understand the basics of satellite orbits • Understand the satellite segment and earth segment • Analyze the various methods of satellite access • Understand the applications of satellites • Understand the basics of satellite Networks UNIT I SATELLITE ORBITS       9 Kepler‟s Laws, Newton‟s law, orbital parameters, orbital perturbations, station keeping, geo stationary and non Geo-stationary orbits – Look Angle Determination- Limits of visibility – eclipse-Sub satellite point –Sun transit outage-Launching Procedures - launch vehicles and propulsion. UNIT II SPACE SEGMENT       9 Spacecraft Technology- Structure, Primary power, Attitude and Orbit control, Thermal control and Propulsion, communication Payload and supporting subsystems, Telemetry, Tracking and
Read more

HS8581 - PROFESSIONAL COMMUNICATION (Syllabus) 2017-regulation Anna University

HS8581 - PROFESSIONAL COMMUNICATION (Syllabus) 2017-regulation Anna University HS8581 PROFESSIONAL COMMUNICATION  LPTC 3003 OBJECTIVES: The course aims to: • Enhance the Employability and Career Skills of students • Orient the students towards grooming as a professional • Make them Employability Graduates • Develop their confidence and help them attend interviews successfully. UNIT I Introduction to Soft Skills-- Hard skills & soft skills - employability and career Skills—Grooming as a professional with values—Time Management—General awareness of Current Affairs UNIT II Self-Introduction-organizing the material - Introducing oneself to the audience – introducing the topic – answering questions – individual presentation practice–– presenting the visuals effectively – 5 minute presentations UNIT III Introduction to Group
Read more

OML751 - TESTING OF MATERIALS (Syllabus) 2017-regulation - Open Elective | Anna University

OML751 - TESTING OF MATERIALS (Syllabus) 2017-regulation - Open Elective | Anna University OML751 TESTING OF MATERIALS  LPTC 3003 OBJECTIVE: To understand the various destructive and non destructive testing methods of materials and its industrial applications. UNIT I INTRODUCTION TO MATERIALS TESTING 9 Overview of materials, Classification of material testing, Purpose of testing, Selection of material, Development of testing, Testing organizations and its committee, Testing standards, Result Analysis, Advantages of testing. UNIT II MECHANICAL TESTING 9 Introduction to mechanical testing, Hardness test (Vickers, Brinell, Rockwell), Tensile test, Impact test (Izod, Charpy) - Principles, Techniques, Methods, Advantages and Limitations, Applications. Bend test, Shear test, Creep and Fatigue test - Principles, Techniques, Methods, Advantages and Limitations, Applications.
Read more